(These brackets have a rating of 250 LBS each. This means that if for example your shelf has 3 brackets it can hold 750 pounds! )

Rapid Shelves Bracket System

 WEIGHT RATING AND USAGE GUIDELINES

The Rapid Shelves bracket system ("Product") is rated to support up to 250 pounds (113 kg) when properly installed according to the manufacturer's instructions. This weight rating assumes even distribution of weight across the shelf surface and proper installation into appropriate support structures. the rating is set at the base closest to the fastened end. Weight unevenly distributed to the end of the bracket may fail to pass the 250pound rating.

DISCLAIMER OF LIABILITY

By purchasing, installing, or using the Product, you ("User") acknowledge and agree to the following terms:

1. **Assumption of Risk**: User assumes all risks associated with the installation and use of the Product, including but not limited to property damage, personal injury, or death.

2. **Proper Installation**: User is solely responsible for ensuring proper installation of the Product in accordance with provided instructions. Improper installation may significantly reduce the weight capacity and stability of the Product.

3. **Weight Limitations**: User agrees not to exceed the stated 250-pound weight rating under any circumstances. User acknowledges that this rating is based on static loads and that dynamic loading (impact forces) may cause failure at lower weights.

4. **Inspection Responsibility**: User is responsible for periodic inspection of the Product for damage, wear, or failure and must discontinue use if such conditions are detected.

5. **Limited Warranty**: Any manufacturer's warranty is limited solely to replacement of defective Products and does not cover any consequential damages.

### RELEASE OF LIABILITY

To the fullest extent permitted by law, Rapid Shelves, its owners, officers, employees, distributors, and agents shall not be liable for any direct, indirect, incidental, special, or consequential damages arising from the use or misuse of the Product, including but not limited to:

- Personal injury or death
- Property damage
- Damage to items stored on or near the Product
- Loss of use or enjoyment of property
- Economic losses or damages

This disclaimer applies regardless of the form of action, whether in contract, tort, negligence, strict product liability, or otherwise, even if Rapid Shelves has been advised of the possibility of such damages.

### INDEMNIFICATION

User agrees to indemnify, defend, and hold harmless Rapid Shelves from any claims, lawsuits, judgments, losses, liabilities, damages, or costs arising from User's installation or use of the Product.

### GOVERNING LAW

This disclaimer shall be governed by and construed in accordance with the laws of [YOUR STATE], without giving effect to any choice of law or conflict of law provisions.

### SEVERABILITY

If any provision of this disclaimer is found to be invalid or unenforceable, the remaining provisions shall remain in full force and effect.

By purchasing, installing, or using the Product, User acknowledges having read and understood this disclaimer and voluntarily assumes all risks associated with the Product's use.

*Last Updated: [03/01/2025]*

Simply slide the bracket onto a stud at the height you want and put in a few screws. That simple!

Installing your Rapid Shelves brackets is quick and easy. 

By using our heavy duty shelf brackets in your storage shed or backyard building you can use all the storage space and keep your space decluttered. 

What You'll Need

- Rapid Shelves brackets
- Provided mounting screws
- Lumber for shelving
- Measuring tape
- Pencil
- Level or chalk line (recommended)
- Drill/screwdriver
- Saw (for cutting lumber)

Installation Steps

Step 1: Mark Your Storage Shelf Height

- Decide where you want your shelf to be positioned
- Measure up from the floor to your desired shelf height
- Make a small mark on each stud where a bracket will be installed
- For a perfectly level shelf, use a level or chalk line to connect your marks

Step 2: Install The Storage Shelf Brackets

- Position the bracket against the stud with the top of the bracket aligned with your mark
- Ensure the bracket is level and square to the wall
- Insert the provided screws through all holes that align with the stud
- Tighten securely with your drill or screwdriver
- Repeat for all brackets at your marked shelf height

Step 3: Prepare Your Shelving Board

- Measure the distance you want to span with your shelf
- Cut your lumber to the appropriate length
- Pro Tip: Position your board to stop at the middle of the dual holes on top of your end bracket—this allows for future expansion of your shelving system

Step 4: Secure Your Heavy Duty Shelving

- Place your cut lumber on top of the installed brackets
- From underneath, drive a small stitch screw through the top hole of each bracket into the underside of your shelf board
- This prevents the board from sliding off the brackets while allowing for easy removal if needed

Step 5: Add More Shelving to your storage shed. (Optional)

- To extend your shelving, simply install another bracket at the same height
- Position a new board to connect with your existing shelf at the middle of the end bracket's dual holes
- Secure with stitch screws as in Step 4

Ready to use your storage shelf!

That's it! Your new shelf is now installed and ready to hold up to 250 pounds of evenly distributed weight. Add additional shelves above or below by repeating these simple steps.

---

Remember:

- Always install brackets directly into wall studs
- Distribute weight evenly across your shelves
- Do not exceed the 250 pound weight rating
- Periodically check that all connections remain secure

Yes, we offer discounts on bulk orders of 12 or more brackets. Contact us for more information.

 Wholesale Partnership Program
 

Increase Your Margins with Rapid Shelves Brackets

Offer your customers the storage solution they need—without the hassle and expense of traditional shelving methods.

THE RAPID SHELVES ADVANTAGE

In an industry where storage solutions are often an afterthought, Rapid Shelves brackets give you a competitive edge that no other shed provider currently offers. Our innovative bracket system transforms ordinary shed space into functional, customizable storage that your customers will value.

 WHY SHED RETAILERS CHOOSE RAPID SHELVES

🔹 Stand Out From Competitors
Be the only shed provider in your market offering this premium storage solution. While competitors sell empty sheds, you'll deliver ready-to-use spaces that solve real storage problems.

🔹 Increase Profit Margins  
Add a high-value, low-cost upgrade option that customers gladly pay for. Our brackets cost significantly less per linear foot than traditional shelving methods while commanding premium pricing.

🔹 Reduce Installation Time and Labor  
Our brackets install in minutes, not hours. Any laborer can perfectly install them without specialized skills or training, reducing your labor costs and increasing efficiency.

🔹 Minimize Inventory Requirements  
The compact design requires minimal warehouse space. Stock a single product that works for multiple shed models and customer needs.

🔹 Use Less Material  
Require up to 40% less lumber than traditional shelving methods. No need for vertical supports means more usable storage space for your customers.

🔹 Offer Customization Without Complexity  
Let customers design their ideal storage configuration without complicating your production process. Our flexible system adapts to any shed size or layout.

 WHOLESALE PRICING & ORDERING

Our wholesale partners enjoy competitive pricing that scales with volume. Contact our wholesale team today to discuss your specific needs and receive a customized quote.

[REQUEST WHOLESALE INFORMATION]

270-590-9403

info@rapidshelves.com

Lifetime warranty is offered on all Rapid Shelves products. Lifetime warranty extends to the original purchaser only and is nontransferable. If a product is defective, it will be replaced free of charge. Proof of purchase is required for all warranty claims. This warranty does not cover products that have been damaged due to misuse, negligence, or normal wear and tear.

We offer a 60-day money back guarantee on Rapid Shelves. We know that you’ll be satisfied with our products, but if for any reason you’re not, we’ll happily refund your purchase

Our brackets come in either 16″ length (good for shelves) or 24″ length (good for lofts and workbenches). Both sizes are 2″ wide.

We use black powder coating for the finish. This ensures our brackets are durable and long-lasting.